summaryrefslogtreecommitdiffstats
path: root/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt')
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt70
1 files changed, 0 insertions, 70 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
deleted file mode 100644
index e47734bee3f0..000000000000
--- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-* UCC (Unified Communications Controllers)
-
-Required properties:
-- device_type : should be "network", "hldc", "uart", "transparent"
- "bisync", "atm", or "serial".
-- compatible : could be "ucc_geth" or "fsl_atm" and so on.
-- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
-- reg : Offset and length of the register set for the device
-- interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
-- interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-- pio-handle : The phandle for the Parallel I/O port configuration.
-- port-number : for UART drivers, the port number to use, between 0 and 3.
- This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
- The port number is added to the minor number of the device. Unlike the
- CPM UART driver, the port-number is required for the QE UART driver.
-- soft-uart : for UART drivers, if specified this means the QE UART device
- driver should use "Soft-UART" mode, which is needed on some SOCs that have
- broken UART hardware. Soft-UART is provided via a microcode upload.
-- rx-clock-name: the UCC receive clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
-- tx-clock-name: the UCC transmit clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
-The following two properties are deprecated. rx-clock has been replaced
-with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
-Drivers that currently use the deprecated properties should continue to
-do so, in order to support older device trees, but they should be updated
-to check for the new properties first.
-- rx-clock : represents the UCC receive clock source.
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-- tx-clock: represents the UCC transmit clock source;
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-
-Required properties for network device_type:
-- mac-address : list of bytes representing the ethernet address.
-- phy-handle : The phandle for the PHY connected to this controller.
-
-Recommended properties:
-- phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
- Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
- "tbi", or "rtbi".
-
-Example:
- ucc@2000 {
- device_type = "network";
- compatible = "ucc_geth";
- cell-index = <1>;
- reg = <2000 200>;
- interrupts = <a0 0>;
- interrupt-parent = <700>;
- mac-address = [ 00 04 9f 00 23 23 ];
- rx-clock = "none";
- tx-clock = "clk9";
- phy-handle = <212000>;
- phy-connection-type = "gmii";
- pio-handle = <140001>;
- };