Merge branch 'for-next/remove-arm-non-pbl' into nextnext

1 files changed, 0 insertions, 475 deletions

diff --git a/arch/arm/boards/sama5d3xek/init.c b/arch/arm/boards/sama5d3xek/init.c
deleted file mode 100644
index b75856198e..0000000000
--- a/arch/arm/boards/sama5d3xek/init.c
+++ /dev/null
@@ -1,475 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-// SPDX-FileCopyrightText: 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
-#include <common.h>
-#include <net.h>
-#include <init.h>
-#include <environment.h>
-#include <asm/armlinux.h>
-#include <asm/mach-types.h>
-#include <fs.h>
-#include <fcntl.h>
-#include <io.h>
-#include <envfs.h>
-#include <mach/at91/hardware.h>
-#include <nand.h>
-#include <linux/sizes.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/rawnand.h>
-#include <mach/at91/board.h>
-#include <mach/at91/at91sam9_smc.h>
-#include <gpio.h>
-#include <mach/at91/iomux.h>
-#include <mach/at91/at91_pmc.h>
-#include <mach/at91/at91_rstc.h>
-#include <mach/at91/at91sam9x5_matrix.h>
-#include <input/qt1070.h>
-#include <readkey.h>
-#include <poller.h>
-#include <linux/w1-gpio.h>
-#include <w1_mac_address.h>
-#include <spi/spi.h>
-#include <linux/clk.h>
-#include <linux/phy.h>
-#include <linux/micrel_phy.h>
-
-#include "hw_version.h"
-
-#ifdef CONFIG_W1_MASTER_GPIO
-struct w1_gpio_platform_data w1_pdata = {
-	.pin = AT91_PIN_PE25,
-	.ext_pullup_enable_pin = -EINVAL,
-	.is_open_drain = 0,
-};
-#endif
-
-#if defined(CONFIG_NAND_ATMEL)
-static struct atmel_nand_data nand_pdata = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= -EINVAL,
-	.enable_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_HW,
-	.has_pmecc	= 1,
-	.pmecc_sector_size = 512,
-	.pmecc_corr_cap = 4,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#endif
-	.on_flash_bbt	= 1,
-};
-
-static struct sam9_smc_config cm_nand_smc_config = {
-	.ncs_read_setup		= 1,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 1,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 5,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 5,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 8,
-	.write_cycle		= 8,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 3,
-
-	.tclr			= 3,
-	.tadl			= 10,
-	.tar			= 3,
-	.ocms			= 0,
-	.trr			= 4,
-	.twb			= 5,
-	.rbnsel			= 3,
-	.nfsel			= 1
-};
-
-static void ek_add_device_nand(void)
-{
-	struct clk *clk = clk_get(NULL, "smc_clk");
-
-	clk_enable(clk);
-
-	/* setup bus-width (8 or 16) */
-	if (nand_pdata.bus_width_16)
-		cm_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		cm_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sama5_smc_configure(0, 3, &cm_nand_smc_config);
-
-	at91_add_device_nand(&nand_pdata);
-}
-#else
-static void ek_add_device_nand(void) {}
-#endif
-
-#if defined(CONFIG_DRIVER_NET_MACB)
-static struct macb_platform_data gmac_pdata = {
-	.phy_interface = PHY_INTERFACE_MODE_RGMII,
-	.phy_addr = -1,
-};
-
-static struct macb_platform_data macb_pdata = {
-	.phy_interface = PHY_INTERFACE_MODE_RMII,
-	.phy_addr = -1,
-};
-
-static bool used_23 = false;
-static bool used_43 = false;
-
-static int ek_register_mac_address_23(int id)
-{
-	if (used_23)
-		return -EBUSY;
-
-	used_23 = true;
-
-	return w1_local_mac_address_register(id, "tml", "w1-23-0");
-}
-
-static int ek_register_mac_address_43(int id)
-{
-	if (used_43)
-		return -EBUSY;
-
-	used_43 = true;
-
-	return w1_local_mac_address_register(id, "tml", "w1-43-0");
-}
-
-static int ksz9021rn_phy_fixup(struct phy_device *phy)
-{
-	int value;
-
-#define GMII_RCCPSR	260
-#define GMII_RRDPSR	261
-#define GMII_ERCR	11
-#define GMII_ERDWR	12
-
-	/* Set delay values */
-	value = GMII_RCCPSR | 0x8000;
-	phy_write(phy, GMII_ERCR, value);
-	value = 0xF2F4;
-	phy_write(phy, GMII_ERDWR, value);
-	value = GMII_RRDPSR | 0x8000;
-	phy_write(phy, GMII_ERCR, value);
-	value = 0x2222;
-	phy_write(phy, GMII_ERDWR, value);
-
-	return 0;
-}
-
-static void ek_add_device_eth(void)
-{
-	if (w1_local_mac_address_register(0, "tml", "w1-2d-0"))
-		if (ek_register_mac_address_23(0))
-			ek_register_mac_address_43(0);
-
-	if (ek_register_mac_address_23(1))
-		ek_register_mac_address_43(1);
-
-	phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
-					   ksz9021rn_phy_fixup);
-
-	at91_add_device_eth(0, &gmac_pdata);
-	at91_add_device_eth(1, &macb_pdata);
-}
-#else
-static void ek_add_device_eth(void) {}
-#endif
-
-#if defined(CONFIG_DRIVER_VIDEO_ATMEL_HLCD)
-/*
- * LCD Controller
- */
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-		.name		= "LG",
-		.refresh	= 60,
-		.xres		= 800,		.yres		= 480,
-		.pixclock	= KHZ2PICOS(33260),
-
-		.left_margin	= 88,		.right_margin	= 168,
-		.upper_margin	= 8,		.lower_margin	= 37,
-		.hsync_len	= 128,		.vsync_len	= 2,
-
-		.sync		= 0,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-/* Default output mode is TFT 24 bit */
-#define BPP_OUT_DEFAULT_LCDCFG5	(LCDC_LCDCFG5_MODE_OUTPUT_24BPP)
-
-/* Driver datas */
-static struct atmel_lcdfb_platform_data ek_lcdc_data = {
-	.lcdcon_is_backlight		= true,
-	.default_bpp			= 16,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= BPP_OUT_DEFAULT_LCDCFG5,
-	.guard_time			= 9,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
-	.mode_list			= at91_tft_vga_modes,
-	.num_modes			= ARRAY_SIZE(at91_tft_vga_modes),
-};
-
-static void ek_add_device_lcdc(void)
-{
-	at91_add_device_lcdc(&ek_lcdc_data);
-}
-
-#else
-static void ek_add_device_lcdc(void) {}
-#endif
-
-#if defined(CONFIG_MCI_ATMEL)
-/*
- * MCI (SD/MMC)
- */
-static struct atmel_mci_platform_data mci0_data = {
-	.bus_width	= 4,
-	.detect_pin	= AT91_PIN_PD17,
-	.wp_pin		= -EINVAL,
-};
-
-static struct atmel_mci_platform_data mci1_data = {
-	.bus_width	= 4,
-	.detect_pin	= AT91_PIN_PD18,
-	.wp_pin		= -EINVAL,
-};
-
-static void ek_add_device_mci(void)
-{
-	/* MMC0 */
-	at91_add_device_mci(0, &mci0_data);
-	/* MMC1 */
-	at91_add_device_mci(1, &mci1_data);
-}
-#else
-static void ek_add_device_mci(void) {}
-#endif
-
-#if defined(CONFIG_I2C_GPIO)
-struct qt1070_platform_data qt1070_pdata = {
-	.irq_pin	= AT91_PIN_PE31,
-};
-
-static struct i2c_board_info i2c_devices[] = {
-	{
-		.platform_data = &qt1070_pdata,
-		I2C_BOARD_INFO("qt1070", 0x1b),
-	},
-};
-
-static void ek_add_device_i2c(void)
-{
-	at91_set_gpio_input(qt1070_pdata.irq_pin, 0);
-	at91_set_deglitch(qt1070_pdata.irq_pin, 1);
-	at91_add_device_i2c(1, i2c_devices, ARRAY_SIZE(i2c_devices));
-	at91_add_device_i2c(0, NULL, 0);
-}
-#else
-static void ek_add_device_i2c(void) {}
-#endif
-
-#if defined(CONFIG_DRIVER_SPI_ATMEL)
-static const struct spi_board_info ek_spi_devices[] = {
-	{
-		.name		= "m25p80",
-		.chip_select	= 0,
-		.max_speed_hz	= 30 * 1000 * 1000,
-		.bus_num	= 0,
-	}
-};
-
-static unsigned spi0_standard_cs[] = { AT91_PIN_PD13 };
-static struct at91_spi_platform_data spi_pdata = {
-	.chipselect = spi0_standard_cs,
-	.num_chipselect = ARRAY_SIZE(spi0_standard_cs),
-};
-
-static void ek_add_device_spi(void)
-{
-	spi_register_board_info(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	at91_add_device_spi(0, &spi_pdata);
-}
-#else
-static void ek_add_device_spi(void) {}
-#endif
-
-#ifdef CONFIG_LED_GPIO
-struct gpio_led leds[] = {
-	{
-		.gpio	= AT91_PIN_PE24,
-		.active_low	= 1,
-		.led	= {
-			.name = "d1",
-		},
-	}, {
-#ifndef CONFIG_W1_MASTER_GPIO
-		.gpio	= AT91_PIN_PE25,
-		.active_low	= 1,
-		.led	= {
-			.name = "d2",
-		},
-#endif
-	},
-};
-
-static void ek_add_led(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(leds); i++) {
-		at91_set_gpio_output(leds[i].gpio, leds[i].active_low);
-		led_gpio_register(&leds[i]);
-	}
-	led_set_trigger(LED_TRIGGER_HEARTBEAT, &leds[0].led);
-}
-#else
-static void ek_add_led(void) {}
-#endif
-
-static int at91sama5d3xek_mem_init(void)
-{
-	at91_add_device_sdram(0);
-
-	return 0;
-}
-mem_initcall(at91sama5d3xek_mem_init);
-
-#ifdef CONFIG_W1_MASTER_GPIO
-static void ek_add_device_w1(void)
-{
-	at91_set_gpio_input(w1_pdata.pin, 0);
-	at91_set_multi_drive(w1_pdata.pin, 1);
-	add_generic_device_res("w1-gpio", DEVICE_ID_SINGLE, NULL, 0, &w1_pdata);
-
-	at91sama5d3xek_devices_detect_hw();
-}
-#else
-static void ek_add_device_w1(void) {}
-#endif
-
-#ifdef CONFIG_POLLER
-/*
- * The SiI9022A (HDMI) and QT1070 share the same irq
- * but if the SiI9022A is not reset the irq is pull down
- * So do it. As the SiI9022A need 1s to reset (500ms up then 500ms down then up)
- * do it poller to do not slow down the boot
- */
-static int hdmi_reset_pin = AT91_PIN_PC31;
-static uint64_t hdmi_reset_start;
-struct poller_struct hdmi_poller;
-
-static void hdmi_on_poller(struct poller_struct *poller)
-{
-	if (!is_timeout_non_interruptible(hdmi_reset_start, 500 * MSECOND))
-		return;
-
-	gpio_set_value(hdmi_reset_pin, 1);
-
-	poller_unregister(poller);
-	ek_add_device_i2c();
-}
-
-static void hdmi_off_poller(struct poller_struct *poller)
-{
-	if (!is_timeout_non_interruptible(hdmi_reset_start, 500 * MSECOND))
-		return;
-
-	gpio_set_value(hdmi_reset_pin, 0);
-
-	hdmi_reset_start = get_time_ns();
-	poller->func = hdmi_on_poller;
-}
-
-static void ek_add_device_hdmi(void)
-{
-	at91_set_gpio_output(hdmi_reset_pin, 1);
-	hdmi_reset_start = get_time_ns();
-	hdmi_poller.func = hdmi_off_poller;
-
-	poller_register(&hdmi_poller, "hdmi-reset");
-}
-#else
-static void ek_add_device_hdmi(void)
-{
-	ek_add_device_i2c();
-}
-#endif
-
-static const struct devfs_partition at91sama5d3xek_nand0_partitions[] = {
-	{
-		.offset = 0x00000,
-		.size = SZ_256K,
-		.flags = DEVFS_PARTITION_FIXED,
-		.name = "at91bootstrap_raw",
-		.bbname = "at91bootstrap",
-	}, {
-		.offset = DEVFS_PARTITION_APPEND, /* 256 KiB */
-		.size = SZ_256K + SZ_128K,
-		.flags = DEVFS_PARTITION_FIXED,
-		.name = "self_raw",
-		.bbname = "self0",
-	},
-	/* hole of 128 KiB */
-	{
-		.offset = SZ_512K + SZ_256K,
-		.size = SZ_256K,
-		.flags = DEVFS_PARTITION_FIXED,
-		.name = "env_raw",
-		.bbname = "env0",
-	}, {
-		.offset = DEVFS_PARTITION_APPEND, /* 1 MiB */
-		.size = SZ_256K,
-		.flags = DEVFS_PARTITION_FIXED,
-		.name = "env_raw1",
-		.bbname = "env1",
-	}, {
-		/* sentinel */
-	}
-};
-
-static int at91sama5d3xek_devices_init(void)
-{
-	ek_add_device_w1();
-	ek_add_device_hdmi();
-	ek_add_device_nand();
-	ek_add_led();
-	ek_add_device_eth();
-	ek_add_device_spi();
-	ek_add_device_mci();
-	ek_add_device_lcdc();
-
-	devfs_create_partitions("nand0", at91sama5d3xek_nand0_partitions);
-
-	if (IS_ENABLED(CONFIG_DEFAULT_ENVIRONMENT_GENERIC))
-		defaultenv_append_directory(defaultenv_sama5d3xek);
-
-	return 0;
-}
-device_initcall(at91sama5d3xek_devices_init);
-
-static int at91sama5d3xek_console_init(void)
-{
-	barebox_set_model("Atmel sama5d3x-ek");
-	barebox_set_hostname("sama5d3x-ek");
-
-	at91_register_uart(0, 0);
-	at91_register_uart(2, 0);
-	return 0;
-}
-console_initcall(at91sama5d3xek_console_init);
-
-static int at91sama5d3xek_main_clock(void)
-{
-	at91_set_main_clock(12000000);
-	return 0;
-}
-pure_initcall(at91sama5d3xek_main_clock);