summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/fpga
diff options
context:
space:
mode:
authorSascha Hauer <s.hauer@pengutronix.de>2017-06-06 08:07:28 +0200
committerSascha Hauer <s.hauer@pengutronix.de>2017-06-06 08:07:28 +0200
commitbb2de9a333d17bb1b048ad208002501226b83f03 (patch)
tree8ef2e876ba43af235c45cb2280885e9c67ba5548 /dts/Bindings/fpga
parent79e6629b02fb3a296b5dc70f16dec0f8d415ccf8 (diff)
downloadbarebox-bb2de9a333d17bb1b048ad208002501226b83f03.tar.gz
dts: update to v4.12-rc1
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Diffstat (limited to 'dts/Bindings/fpga')
-rw-r--r--dts/Bindings/fpga/altera-pr-ip.txt12
-rw-r--r--dts/Bindings/fpga/fpga-region.txt3
-rw-r--r--dts/Bindings/fpga/lattice-ice40-fpga-mgr.txt21
-rw-r--r--dts/Bindings/fpga/xilinx-slave-serial.txt44
4 files changed, 80 insertions, 0 deletions
diff --git a/dts/Bindings/fpga/altera-pr-ip.txt b/dts/Bindings/fpga/altera-pr-ip.txt
new file mode 100644
index 0000000..52a294c
--- /dev/null
+++ b/dts/Bindings/fpga/altera-pr-ip.txt
@@ -0,0 +1,12 @@
+Altera Arria10 Partial Reconfiguration IP
+
+Required properties:
+- compatible : should contain "altr,a10-pr-ip"
+- reg : base address and size for memory mapped io.
+
+Example:
+
+ fpga_mgr: fpga-mgr@ff20c000 {
+ compatible = "altr,a10-pr-ip";
+ reg = <0xff20c000 0x10>;
+ };
diff --git a/dts/Bindings/fpga/fpga-region.txt b/dts/Bindings/fpga/fpga-region.txt
index 3b32ba1..6db8aed 100644
--- a/dts/Bindings/fpga/fpga-region.txt
+++ b/dts/Bindings/fpga/fpga-region.txt
@@ -186,12 +186,15 @@ Optional properties:
otherwise full reconfiguration is done.
- external-fpga-config : boolean, set if the FPGA has already been configured
prior to OS boot up.
+- encrypted-fpga-config : boolean, set if the bitstream is encrypted
- region-unfreeze-timeout-us : The maximum time in microseconds to wait for
bridges to successfully become enabled after the region has been
programmed.
- region-freeze-timeout-us : The maximum time in microseconds to wait for
bridges to successfully become disabled before the region has been
programmed.
+- config-complete-timeout-us : The maximum time in microseconds time for the
+ FPGA to go to operating mode after the region has been programmed.
- child nodes : devices in the FPGA after programming.
In the example below, when an overlay is applied targeting fpga-region0,
diff --git a/dts/Bindings/fpga/lattice-ice40-fpga-mgr.txt b/dts/Bindings/fpga/lattice-ice40-fpga-mgr.txt
new file mode 100644
index 0000000..4dc4124
--- /dev/null
+++ b/dts/Bindings/fpga/lattice-ice40-fpga-mgr.txt
@@ -0,0 +1,21 @@
+Lattice iCE40 FPGA Manager
+
+Required properties:
+- compatible: Should contain "lattice,ice40-fpga-mgr"
+- reg: SPI chip select
+- spi-max-frequency: Maximum SPI frequency (>=1000000, <=25000000)
+- cdone-gpios: GPIO input connected to CDONE pin
+- reset-gpios: Active-low GPIO output connected to CRESET_B pin. Note
+ that unless the GPIO is held low during startup, the
+ FPGA will enter Master SPI mode and drive SCK with a
+ clock signal potentially jamming other devices on the
+ bus until the firmware is loaded.
+
+Example:
+ fpga: fpga@0 {
+ compatible = "lattice,ice40-fpga-mgr";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ cdone-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
diff --git a/dts/Bindings/fpga/xilinx-slave-serial.txt b/dts/Bindings/fpga/xilinx-slave-serial.txt
new file mode 100644
index 0000000..9766f74
--- /dev/null
+++ b/dts/Bindings/fpga/xilinx-slave-serial.txt
@@ -0,0 +1,44 @@
+Xilinx Slave Serial SPI FPGA Manager
+
+Xilinx Spartan-6 FPGAs support a method of loading the bitstream over
+what is referred to as "slave serial" interface.
+The slave serial link is not technically SPI, and might require extra
+circuits in order to play nicely with other SPI slaves on the same bus.
+
+See https://www.xilinx.com/support/documentation/user_guides/ug380.pdf
+
+Required properties:
+- compatible: should contain "xlnx,fpga-slave-serial"
+- reg: spi chip select of the FPGA
+- prog_b-gpios: config pin (referred to as PROGRAM_B in the manual)
+- done-gpios: config status pin (referred to as DONE in the manual)
+
+Example for full FPGA configuration:
+
+ fpga-region0 {
+ compatible = "fpga-region";
+ fpga-mgr = <&fpga_mgr_spi>;
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ };
+
+ spi1: spi@10680 {
+ compatible = "marvell,armada-xp-spi", "marvell,orion-spi";
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <92>;
+ clocks = <&coreclk 0>;
+ status = "okay";
+
+ fpga_mgr_spi: fpga-mgr@0 {
+ compatible = "xlnx,fpga-slave-serial";
+ spi-max-frequency = <60000000>;
+ spi-cpha;
+ reg = <0>;
+ done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ };
+ };