dts: update to v4.3-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

2 files changed, 61 insertions, 8 deletions

diff --git a/dts/Bindings/media/i2c/adv7604.txt b/dts/Bindings/media/i2c/adv7604.txt
index c27cede3bd..8337f75c75 100644
--- a/dts/Bindings/media/i2c/adv7604.txt
+++ b/dts/Bindings/media/i2c/adv7604.txt
@@ -1,15 +1,17 @@
-* Analog Devices ADV7604/11 video decoder with HDMI receiver
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
 
-The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI
-receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input,
-and the ADV7611 has one HDMI input and no analog input.
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
 
-These device tree bindings support the ADV7611 only at the moment.
+These device tree bindings support the ADV7611/12 only at the moment.
 
 Required Properties:
 
   - compatible: Must contain one of the following
     - "adi,adv7611" for the ADV7611
+    - "adi,adv7612" for the ADV7612
 
   - reg: I2C slave address
 
@@ -22,10 +24,10 @@ port, in accordance with the video interface bindings defined in
 Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
 are numbered as follows.
 
-  Port			ADV7611
+  Port			ADV7611    ADV7612
 ------------------------------------------------------------
-  HDMI			0
-  Digital output	1
+  HDMI			0             0, 1
+  Digital output	1                2
 
 The digital output port node must contain at least one endpoint.
 
@@ -45,6 +47,7 @@ Optional Endpoint Properties:
   If none of hsync-active, vsync-active and pclk-sample is specified the
   endpoint will use embedded BT.656 synchronization.
 
+  - default-input: Select which input is selected after reset.
 
 Example:
 
@@ -58,6 +61,8 @@ Example:
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		default-input = <0>;
+
 		port@0 {
 			reg = <0>;
 		};
diff --git a/dts/Bindings/media/i2c/tc358743.txt b/dts/Bindings/media/i2c/tc358743.txt
new file mode 100644
index 0000000000..5218921629
--- /dev/null
+++ b/dts/Bindings/media/i2c/tc358743.txt
@@ -0,0 +1,48 @@
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+		       source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts, interrupt-parent: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+	      or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+		       MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+		    expressed as a 64-bit big-endian integer. The frequency
+		    is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	tc358743@0f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};