Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

4 files changed, 109 insertions, 0 deletions

diff --git a/dts/Bindings/power/bq2415x.txt b/dts/Bindings/power/bq2415x.txt
new file mode 100644
index 0000000000..d0327f0b59
--- /dev/null
+++ b/dts/Bindings/power/bq2415x.txt
@@ -0,0 +1,47 @@
+Binding for TI bq2415x Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24150"
+ * "ti,bq24150"
+ * "ti,bq24150a"
+ * "ti,bq24151"
+ * "ti,bq24151a"
+ * "ti,bq24152"
+ * "ti,bq24153"
+ * "ti,bq24153a"
+ * "ti,bq24155"
+ * "ti,bq24156"
+ * "ti,bq24156a"
+ * "ti,bq24158"
+- reg:			   integer, i2c address of the device.
+- ti,current-limit:	   integer, initial maximum current charger can pull
+			   from power supply in mA.
+- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
+			   The chip will use slow precharge if battery voltage
+			   is below this value.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
+- ti,charge-current:	   integer, maximum charging current in mA.
+- ti,termination-current:  integer, charge will be terminated when current in
+			   constant-voltage phase drops below this value (in mA).
+- ti,resistor-sense:	   integer, value of sensing resistor in milliohm.
+
+Optional properties:
+- ti,usb-charger-detection: phandle to usb charger detection device.
+			    (required for auto mode)
+
+Example from Nokia N900:
+
+bq24150a {
+	compatible = "ti,bq24150a";
+	reg = <0x6b>;
+
+	ti,current-limit = <100>;
+	ti,weak-battery-voltage = <3400>;
+	ti,battery-regulation-voltage = <4200>;
+	ti,charge-current = <650>;
+	ti,termination-current = <100>;
+	ti,resistor-sense = <68>;
+
+	ti,usb-charger-detection = <&isp1704>;
+};
diff --git a/dts/Bindings/power/isp1704.txt b/dts/Bindings/power/isp1704.txt
new file mode 100644
index 0000000000..fa35969079
--- /dev/null
+++ b/dts/Bindings/power/isp1704.txt
@@ -0,0 +1,17 @@
+Binding for NXP ISP1704 USB Charger Detection
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nxp,isp1704"
+- nxp,enable-gpio: Should contain a phandle + gpio-specifier
+  to the GPIO pin connected to the chip's enable pin.
+- usb-phy: Should contain a phandle to the USB PHY
+  the ISP1704 is connected to.
+
+Example:
+
+isp1704 {
+	compatible = "nxp,isp1704";
+	nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+	usb-phy = <&usb2_phy>;
+};
diff --git a/dts/Bindings/power/opp.txt b/dts/Bindings/power/opp.txt
new file mode 100644
index 0000000000..74499e5033
--- /dev/null
+++ b/dts/Bindings/power/opp.txt
@@ -0,0 +1,25 @@
+* Generic OPP Interface
+
+SoCs have a standard set of tuples consisting of frequency and
+voltage pairs that the device will support per voltage domain. These
+are called Operating Performance Points or OPPs.
+
+Properties:
+- operating-points: An array of 2-tuples items, and each item consists
+  of frequency and voltage like <freq-kHz vol-uV>.
+	freq: clock frequency in kHz
+	vol: voltage in microvolt
+
+Examples:
+
+cpu@0 {
+	compatible = "arm,cortex-a9";
+	reg = <0>;
+	next-level-cache = <&L2>;
+	operating-points = <
+		/* kHz    uV */
+		792000  1100000
+		396000  950000
+		198000  850000
+	>;
+};
diff --git a/dts/Bindings/power/twl-charger.txt b/dts/Bindings/power/twl-charger.txt
new file mode 100644
index 0000000000..d5c706216d
--- /dev/null
+++ b/dts/Bindings/power/twl-charger.txt
@@ -0,0 +1,20 @@
+TWL BCI (Battery Charger Interface)
+
+Required properties:
+- compatible:
+  - "ti,twl4030-bci"
+- interrupts: two interrupt lines from the TWL SIH (secondary
+  interrupt handler) - interrupts 9 and 2.
+
+Optional properties:
+- ti,bb-uvolt: microvolts for charging the backup battery.
+- ti,bb-uamp: microamps for charging the backup battery.
+
+Examples:
+
+bci {
+   compatible = "ti,twl4030-bci";
+   interrupts = <9>, <2>;
+   ti,bb-uvolt = <3200000>;
+   ti,bb-uamp = <150>;
+};