Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 83 insertions, 0 deletions

diff --git a/dts/Bindings/usb/fsl-usb.txt b/dts/Bindings/usb/fsl-usb.txt
new file mode 100644
index 0000000000..4779c029b6
--- /dev/null
+++ b/dts/Bindings/usb/fsl-usb.txt
@@ -0,0 +1,83 @@
+Freescale SOC USB controllers
+
+The device node for a USB controller that is part of a Freescale
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "fsl-usb2-mph" for multi port host USB
+   controllers, or "fsl-usb2-dr" for dual role USB controllers
+   or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121.
+   Wherever applicable, the IP version of the USB controller should
+   also be mentioned (for eg. fsl-usb2-dr-v2.2 for bsc9132).
+ - phy_type : For multi port host USB controllers, should be one of
+   "ulpi", or "serial". For dual role USB controllers, should be
+   one of "ulpi", "utmi", "utmi_wide", or "serial".
+ - reg : Offset and length of the register set for the device
+ - port0 : boolean; if defined, indicates port0 is connected for
+   fsl-usb2-mph compatible controllers.  Either this property or
+   "port1" (or both) must be defined for "fsl-usb2-mph" compatible
+   controllers.
+ - port1 : boolean; if defined, indicates port1 is connected for
+   fsl-usb2-mph compatible controllers.  Either this property or
+   "port0" (or both) must be defined for "fsl-usb2-mph" compatible
+   controllers.
+ - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
+   controllers.  Can be "host", "peripheral", or "otg".  Default to
+   "host" if not defined for backward compatibility.
+
+Recommended properties :
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+
+Optional properties :
+ - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the
+   port power polarity of internal PHY signal DRVVBUS is inverted.
+ - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates
+   the PWR_FAULT signal polarity is inverted.
+
+Example multi port host USB controller device node :
+	usb@22000 {
+		compatible = "fsl-usb2-mph";
+		reg = <22000 1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <700>;
+		interrupts = <27 1>;
+		phy_type = "ulpi";
+		port0;
+		port1;
+	};
+
+Example dual role USB controller device node :
+	usb@23000 {
+		compatible = "fsl-usb2-dr";
+		reg = <23000 1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <700>;
+		interrupts = <26 1>;
+		dr_mode = "otg";
+		phy = "ulpi";
+	};
+
+Example dual role USB controller device node for MPC5121ADS:
+
+	usb@4000 {
+		compatible = "fsl,mpc5121-usb2-dr";
+		reg = <0x4000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = < &ipic >;
+		interrupts = <44 0x8>;
+		dr_mode = "otg";
+		phy_type = "utmi_wide";
+		fsl,invert-drvvbus;
+		fsl,invert-pwr-fault;
+	};