Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 136 insertions, 0 deletions

diff --git a/dts/src/arm/dove-cubox.dts b/dts/src/arm/dove-cubox.dts
new file mode 100644
index 0000000000..7a70f4ca50
--- /dev/null
+++ b/dts/src/arm/dove-cubox.dts
@@ -0,0 +1,136 @@
+/dts-v1/;
+
+#include "dove.dtsi"
+
+/ {
+	model = "SolidRun CuBox";
+	compatible = "solidrun,cubox", "marvell,dove";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_gpio_18>;
+		pinctrl-names = "default";
+
+		power {
+			label = "Power";
+			gpios = <&gpio0 18 1>;
+			default-state = "keep";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 1 0>;
+			pinctrl-0 = <&pmx_gpio_1>;
+			pinctrl-names = "default";
+		};
+	};
+
+	clocks {
+		/* 25MHz reference crystal */
+		ref25: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+	};
+
+	ir_recv: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 19 1>;
+		pinctrl-0 = <&pmx_gpio_19>;
+		pinctrl-names = "default";
+	};
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+&ethphy {
+	compatible = "marvell,88e1310";
+	reg = <1>;
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	si5351: clock-generator {
+		compatible = "silabs,si5351a-msop";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#clock-cells = <1>;
+
+		/* connect xtal input to 25MHz reference */
+		clocks = <&ref25>;
+
+		/* connect xtal input as source of pll0 and pll1 */
+		silabs,pll-source = <0 0>, <1 0>;
+
+		clkout0 {
+			reg = <0>;
+			silabs,drive-strength = <8>;
+			silabs,multisynth-source = <0>;
+			silabs,clock-source = <0>;
+			silabs,pll-master;
+		};
+
+		clkout2 {
+			reg = <2>;
+			silabs,drive-strength = <8>;
+			silabs,multisynth-source = <1>;
+			silabs,clock-source = <0>;
+			silabs,pll-master;
+		};
+	};
+};
+
+&sdio0 {
+	status = "okay";
+	/* sdio0 card detect is connected to wrong pin on CuBox */
+	cd-gpios = <&gpio0 12 1>;
+	pinctrl-0 = <&pmx_sdio0 &pmx_gpio_12>;
+};
+
+&spi0 {
+	status = "okay";
+
+	/* spi0.0: 4M Flash Winbond W25Q32BV */
+	spi-flash@0 {
+		compatible = "st,w25q32";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&audio1 {
+	status = "okay";
+	clocks = <&gate_clk 13>, <&si5351 2>;
+	clock-names = "internal", "extclk";
+	pinctrl-0 = <&pmx_audio1_i2s1_spdifo &pmx_audio1_extclk>;
+	pinctrl-names = "default";
+};