1 files changed, 0 insertions, 121 deletions
diff --git a/dts/Bindings/pinctrl/qcom,msm8974-pinctrl.txt b/dts/Bindings/pinctrl/qcom,msm8974-pinctrl.txt
deleted file mode 100644
index 0040565066..0000000000
--- a/dts/Bindings/pinctrl/qcom,msm8974-pinctrl.txt
+++ /dev/null
@@ -1,121 +0,0 @@
-Qualcomm MSM8974 TLMM block
-
-Required properties:
-- compatible: "qcom,msm8974-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
-                The first cell is the gpio pin number and the
-                second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-Qualcomm's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength.
-
-Non-empty subnodes must specify the 'pins' property.
-Note that not all properties are valid for all pins.
-
-
-Valid values for pins are:
-  gpio0-gpio145
-    Supports mux, bias and drive-strength
-
-  sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
-    Supports bias and drive-strength
-
-  hsic_data, hsic_strobe
-    Supports only mux
-
-Valid values for function are:
-  cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
-  blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
-  blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2,
-  blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3,
-  blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4,
-  blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
-  blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6,
-  blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7,
-  blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8,
-  blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9,
-  blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
-  blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11,
-  blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12,
-  blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
-  blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
-  sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1,
-  cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2,
-  cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
-  hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
-  gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
-  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio
-
-  (Note that this is not yet the complete list of functions)
-
-
-
-Example:
-
-	msmgpio: pinctrl@fd510000 {
-		compatible = "qcom,msm8974-pinctrl";
-		reg = <0xfd510000 0x4000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&msmgpio 0 0 146>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 208 0>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&uart2_default>;
-
-		uart2_default: uart2_default {
-			mux {
-				pins = "gpio4", "gpio5";
-				function = "blsp_uart2";
-			};
-
-			tx {
-				pins = "gpio4";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio5";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-	};