diff options
Diffstat (limited to 'dts/Bindings/power/reset')
-rw-r--r-- | dts/Bindings/power/reset/gpio-poweroff.txt | 41 | ||||
-rw-r--r-- | dts/Bindings/power/reset/gpio-poweroff.yaml | 59 | ||||
-rw-r--r-- | dts/Bindings/power/reset/gpio-restart.txt | 54 | ||||
-rw-r--r-- | dts/Bindings/power/reset/gpio-restart.yaml | 86 |
4 files changed, 145 insertions, 95 deletions
diff --git a/dts/Bindings/power/reset/gpio-poweroff.txt b/dts/Bindings/power/reset/gpio-poweroff.txt deleted file mode 100644 index 3e56c1b34a..0000000000 --- a/dts/Bindings/power/reset/gpio-poweroff.txt +++ /dev/null @@ -1,41 +0,0 @@ -Driver a GPIO line that can be used to turn the power off. - -The driver supports both level triggered and edge triggered power off. -At driver load time, the driver will request the given gpio line and -install a handler to power off the system. If the optional properties -'input' is not found, the GPIO line will be driven in the inactive -state. Otherwise its configured as an input. - -When the power-off handler is called, the gpio is configured as an -output, and drive active, so triggering a level triggered power off -condition. This will also cause an inactive->active edge condition, so -triggering positive edge triggered power off. After a delay of 100ms, -the GPIO is set to inactive, thus causing an active->inactive edge, -triggering negative edge triggered power off. After another 100ms -delay the GPIO is driver active again. If the power is still on and -the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. - -Required properties: -- compatible : should be "gpio-poweroff". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to power down the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- input : Initially configure the GPIO line as an input. Only reconfigure - it to an output when the power-off handler is called. If this optional - property is not specified, the GPIO is initialized as an output in its - inactive state. -- active-delay-ms: Delay (default 100) to wait after driving gpio active -- inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive -- timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is - specified, 3000 ms is used. - -Examples: - -gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; - timeout-ms = <3000>; -}; diff --git a/dts/Bindings/power/reset/gpio-poweroff.yaml b/dts/Bindings/power/reset/gpio-poweroff.yaml new file mode 100644 index 0000000000..45d66c7751 --- /dev/null +++ b/dts/Bindings/power/reset/gpio-poweroff.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/reset/gpio-poweroff.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controlled power off + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: > + System power off support via a GPIO line. When a shutdown is + executed the operating system is expected to switch the GPIO + from inactive to active. After a delay (active-delay-ms) it + is expected to be switched back to inactive. After another + delay (inactive-delay-ms) it is configured as active again. + Finally the operating system assumes the power off failed if + the system is still running after waiting some time (timeout-ms). + +properties: + compatible: + const: gpio-poweroff + + gpios: + maxItems: 1 + + input: + type: boolean + description: > + Initially configure the GPIO line as an input. Only reconfigure + it to an output when the power-off sequence is initiated. If this optional + property is not specified, the GPIO is initialized as an output in its inactive state. + + active-delay-ms: + default: 100 + description: Delay to wait after driving gpio active + + inactive-delay-ms: + default: 100 + description: Delay to wait after driving gpio inactive + + timeout-ms: + default: 3000 + description: Time to wait before assuming the power off sequence failed. + +required: + - compatible + - gpios + +additionalProperties: false + +examples: + - | + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; + timeout-ms = <3000>; + }; diff --git a/dts/Bindings/power/reset/gpio-restart.txt b/dts/Bindings/power/reset/gpio-restart.txt deleted file mode 100644 index af3701bc15..0000000000 --- a/dts/Bindings/power/reset/gpio-restart.txt +++ /dev/null @@ -1,54 +0,0 @@ -Drive a GPIO line that can be used to restart the system from a restart -handler. - -This binding supports level and edge triggered reset. At driver load -time, the driver will request the given gpio line and install a restart -handler. If the optional properties 'open-source' is not found, the GPIO line -will be driven in the inactive state. Otherwise its not driven until -the restart is initiated. - -When the system is restarted, the restart handler will be invoked in -priority order. The gpio is configured as an output, and driven active, -triggering a level triggered reset condition. This will also cause an -inactive->active edge condition, triggering positive edge triggered -reset. After a delay specified by active-delay, the GPIO is set to -inactive, thus causing an active->inactive edge, triggering negative edge -triggered reset. After a delay specified by inactive-delay, the GPIO -is driven active again. After a delay specified by wait-delay, the -restart handler completes allowing other restart handlers to be attempted. - -Required properties: -- compatible : should be "gpio-restart". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to reset the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- open-source : Treat the GPIO as being open source and defer driving - it to when the restart is initiated. If this optional property is not - specified, the GPIO is initialized as an output in its inactive state. -- priority : A priority ranging from 0 to 255 (default 128) according to - the following guidelines: - 0: Restart handler of last resort, with limited restart - capabilities - 128: Default restart handler; use if no other restart handler is - expected to be available, and/or if restart functionality is - sufficient to restart the entire system - 255: Highest priority restart handler, will preempt all other - restart handlers -- active-delay: Delay (default 100) to wait after driving gpio active [ms] -- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] -- wait-delay: Delay (default 3000) to wait after completing restart - sequence [ms] - -Examples: - -gpio-restart { - compatible = "gpio-restart"; - gpios = <&gpio 4 0>; - priority = <128>; - active-delay = <100>; - inactive-delay = <100>; - wait-delay = <3000>; -}; diff --git a/dts/Bindings/power/reset/gpio-restart.yaml b/dts/Bindings/power/reset/gpio-restart.yaml new file mode 100644 index 0000000000..a72d5c7215 --- /dev/null +++ b/dts/Bindings/power/reset/gpio-restart.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/reset/gpio-restart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controlled reset + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +description: > + Drive a GPIO line that can be used to restart the system from a restart handler. + + This binding supports level and edge triggered reset. At driver load time, the driver will + request the given gpio line and install a restart handler. If the optional properties + 'open-source' is not found, the GPIO line will be driven in the inactive state. Otherwise its + not driven until the restart is initiated. + + When the system is restarted, the restart handler will be invoked in priority order. The GPIO + is configured as an output, and driven active, triggering a level triggered reset condition. + This will also cause an inactive->active edge condition, triggering positive edge triggered + reset. After a delay specified by active-delay, the GPIO is set to inactive, thus causing an + active->inactive edge, triggering negative edge triggered reset. After a delay specified by + inactive-delay, the GPIO is driven active again. After a delay specified by wait-delay, the + restart handler completes allowing other restart handlers to be attempted. + +properties: + compatible: + const: gpio-restart + + gpios: + description: The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be low to reset the board + set it to "Active Low", otherwise set GPIO to "Active High". + + open-source: + $ref: /schemas/types.yaml#/definitions/flag + description: Treat the GPIO as being open source and defer driving it to when the restart is + initiated. If this optional property is not specified, the GPIO is initialized as an output + in its inactive state. + + priority: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + A priority ranging from 0 to 255 (default 129) according to the following guidelines: + + 0: Restart handler of last resort, with limited restart capabilities. + 128: Default restart handler; use if no other restart handler is expected to be available, + and/or if restart functionality is sufficient to restart the entire system. + 255: Highest priority restart handler, will preempt all other restart handlers. + minimum: 0 + maximum: 255 + default: 129 + + active-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Delay (default 100) to wait after driving gpio active [ms] + default: 100 + + inactive-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Delay (default 100) to wait after driving gpio inactive [ms] + default: 100 + + wait-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Delay (default 3000) to wait after completing restart sequence [ms] + default: 100 + +additionalProperties: false + +required: + - compatible + - gpios + +examples: + - | + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; + }; |