diff options
Diffstat (limited to 'dts/Bindings/serial')
| -rw-r--r-- | dts/Bindings/serial/amlogic,meson-uart.yaml | 2 | ||||
| -rw-r--r-- | dts/Bindings/serial/fsl-imx-uart.txt | 6 | ||||
| -rw-r--r-- | dts/Bindings/serial/fsl-lpuart.txt | 10 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,hscif.yaml | 135 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,sci-serial.txt | 150 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,sci.yaml | 69 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,scif.yaml | 172 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,scifa.yaml | 107 | ||||
| -rw-r--r-- | dts/Bindings/serial/renesas,scifb.yaml | 98 | ||||
| -rw-r--r-- | dts/Bindings/serial/serial.txt | 56 | ||||
| -rw-r--r-- | dts/Bindings/serial/serial.yaml | 131 | ||||
| -rw-r--r-- | dts/Bindings/serial/slave-device.txt | 45 | ||||
| -rw-r--r-- | dts/Bindings/serial/snps-dw-apb-uart.yaml | 1 | ||||
| -rw-r--r-- | dts/Bindings/serial/socionext,uniphier-uart.yaml | 46 | ||||
| -rw-r--r-- | dts/Bindings/serial/uniphier-uart.txt | 22 |
15 files changed, 772 insertions, 278 deletions
diff --git a/dts/Bindings/serial/amlogic,meson-uart.yaml b/dts/Bindings/serial/amlogic,meson-uart.yaml index 214fe8bedd..d4178ab0d6 100644 --- a/dts/Bindings/serial/amlogic,meson-uart.yaml +++ b/dts/Bindings/serial/amlogic,meson-uart.yaml @@ -62,6 +62,8 @@ required: - clocks - clock-names +additionalProperties: false + examples: - | serial@84c0 { diff --git a/dts/Bindings/serial/fsl-imx-uart.txt b/dts/Bindings/serial/fsl-imx-uart.txt index 35957cbf15..9582fc2279 100644 --- a/dts/Bindings/serial/fsl-imx-uart.txt +++ b/dts/Bindings/serial/fsl-imx-uart.txt @@ -8,6 +8,10 @@ Required properties: Optional properties: - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. +- fsl,inverted-tx , fsl,inverted-rx : Indicate that the hardware attached + to the peripheral inverts the signal transmitted or received, + respectively, and that the peripheral should invert its output/input + using the INVT/INVR registers. - rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt. Note that for RS485 you must enable either the "uart-has-rtscts" or the "rts-gpios" @@ -15,7 +19,7 @@ Optional properties: the transceiver is actually CTS_B, not RTS_B. CTS_B is always output, and RTS_B is input, regardless of dte-mode. -Please check Documentation/devicetree/bindings/serial/serial.txt +Please check Documentation/devicetree/bindings/serial/serial.yaml for the complete list of generic properties. Note: Each uart controller should have an alias correctly numbered diff --git a/dts/Bindings/serial/fsl-lpuart.txt b/dts/Bindings/serial/fsl-lpuart.txt index c904e2e683..e7448b92dd 100644 --- a/dts/Bindings/serial/fsl-lpuart.txt +++ b/dts/Bindings/serial/fsl-lpuart.txt @@ -6,6 +6,8 @@ Required properties: on Vybrid vf610 SoC with 8-bit register organization - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated on LS1021A SoC with 32-bit big-endian register organization + - "fsl,ls1028a-lpuart" for lpuart compatible with the one integrated + on LS1028A SoC with 32-bit little-endian register organization - "fsl,imx7ulp-lpuart" for lpuart compatible with the one integrated on i.MX7ULP SoC with 32-bit little-endian register organization - "fsl,imx8qxp-lpuart" for lpuart compatible with the one integrated @@ -15,10 +17,10 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names -- clock-names : For vf610/ls1021a/imx7ulp, "ipg" clock is for uart bus/baud - clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used to access - lpuart controller registers, it also requires "baud" clock for module to - receive/transmit data. +- clock-names : For vf610/ls1021a/ls1028a/imx7ulp, "ipg" clock is for uart + bus/baud clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used + to access lpuart controller registers, it also requires "baud" clock for + module to receive/transmit data. Optional properties: - dmas: A list of two dma specifiers, one for each entry in dma-names. diff --git a/dts/Bindings/serial/renesas,hscif.yaml b/dts/Bindings/serial/renesas,hscif.yaml new file mode 100644 index 0000000000..91101521ef --- /dev/null +++ b/dts/Bindings/serial/renesas,hscif.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,hscif.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas High Speed Serial Communication Interface with FIFO (HSCIF) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,hscif-r8a7778 # R-Car M1 + - renesas,hscif-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-hscif # R-Car Gen1 + - const: renesas,hscif # generic HSCIF compatible UART + + - items: + - enum: + - renesas,hscif-r8a7743 # RZ/G1M + - renesas,hscif-r8a7744 # RZ/G1N + - renesas,hscif-r8a7745 # RZ/G1E + - renesas,hscif-r8a77470 # RZ/G1C + - renesas,hscif-r8a7790 # R-Car H2 + - renesas,hscif-r8a7791 # R-Car M2-W + - renesas,hscif-r8a7792 # R-Car V2H + - renesas,hscif-r8a7793 # R-Car M2-N + - renesas,hscif-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-hscif # R-Car Gen2 and RZ/G1 + - const: renesas,hscif # generic HSCIF compatible UART + + - items: + - enum: + - renesas,hscif-r8a774a1 # RZ/G2M + - renesas,hscif-r8a774b1 # RZ/G2N + - renesas,hscif-r8a774c0 # RZ/G2E + - renesas,hscif-r8a7795 # R-Car H3 + - renesas,hscif-r8a7796 # R-Car M3-W + - renesas,hscif-r8a77961 # R-Car M3-W+ + - renesas,hscif-r8a77965 # R-Car M3-N + - renesas,hscif-r8a77970 # R-Car V3M + - renesas,hscif-r8a77980 # R-Car V3H + - renesas,hscif-r8a77990 # R-Car E3 + - renesas,hscif-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-hscif # R-Car Gen3 and RZ/G2 + - const: renesas,hscif # generic HSCIF compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + enum: + - fck # UART functional clock + - hsck # optional external clock input + - brg_int # optional internal clock source for BRG frequency divider + - scif_clk # optional external clock source for BRG frequency divider + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-hscif + - renesas,rcar-gen3-hscif +then: + required: + - resets + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + aliases { + serial1 = &hscif1; + }; + + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a7795", "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0xe6550000 96>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 519>, <&cpg CPG_CORE R8A7795_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x33>, <&dmac1 0x32>, <&dmac2 0x33>, <&dmac2 0x32>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 519>; + uart-has-rtscts; + }; diff --git a/dts/Bindings/serial/renesas,sci-serial.txt b/dts/Bindings/serial/renesas,sci-serial.txt deleted file mode 100644 index a5edf4b70c..0000000000 --- a/dts/Bindings/serial/renesas,sci-serial.txt +++ /dev/null @@ -1,150 +0,0 @@ -* Renesas SH-Mobile Serial Communication Interface - -Required properties: - - - compatible: Must contain one or more of the following: - - - "renesas,scif-r7s72100" for R7S72100 (RZ/A1H) SCIF compatible UART. - - "renesas,scif-r7s9210" for R7S9210 (RZ/A2) SCIF compatible UART. - - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. - - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. - - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. - - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. - - "renesas,scif-r8a7743" for R8A7743 (RZ/G1M) SCIF compatible UART. - - "renesas,scifa-r8a7743" for R8A7743 (RZ/G1M) SCIFA compatible UART. - - "renesas,scifb-r8a7743" for R8A7743 (RZ/G1M) SCIFB compatible UART. - - "renesas,hscif-r8a7743" for R8A7743 (RZ/G1M) HSCIF compatible UART. - - "renesas,scif-r8a7744" for R8A7744 (RZ/G1N) SCIF compatible UART. - - "renesas,scifa-r8a7744" for R8A7744 (RZ/G1N) SCIFA compatible UART. - - "renesas,scifb-r8a7744" for R8A7744 (RZ/G1N) SCIFB compatible UART. - - "renesas,hscif-r8a7744" for R8A7744 (RZ/G1N) HSCIF compatible UART. - - "renesas,scif-r8a7745" for R8A7745 (RZ/G1E) SCIF compatible UART. - - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. - - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. - - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. - - "renesas,scif-r8a77470" for R8A77470 (RZ/G1C) SCIF compatible UART. - - "renesas,hscif-r8a77470" for R8A77470 (RZ/G1C) HSCIF compatible UART. - - "renesas,scif-r8a774a1" for R8A774A1 (RZ/G2M) SCIF compatible UART. - - "renesas,hscif-r8a774a1" for R8A774A1 (RZ/G2M) HSCIF compatible UART. - - "renesas,scif-r8a774b1" for R8A774B1 (RZ/G2N) SCIF compatible UART. - - "renesas,hscif-r8a774b1" for R8A774B1 (RZ/G2N) HSCIF compatible UART. - - "renesas,scif-r8a774c0" for R8A774C0 (RZ/G2E) SCIF compatible UART. - - "renesas,hscif-r8a774c0" for R8A774C0 (RZ/G2E) HSCIF compatible UART. - - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - - "renesas,hscif-r8a7778" for R8A7778 (R-Car M1) HSCIF compatible UART. - - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - - "renesas,hscif-r8a7779" for R8A7779 (R-Car H1) HSCIF compatible UART. - - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. - - "renesas,hscif-r8a7790" for R8A7790 (R-Car H2) HSCIF compatible UART. - - "renesas,scif-r8a7791" for R8A7791 (R-Car M2-W) SCIF compatible UART. - - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2-W) SCIFA compatible UART. - - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2-W) SCIFB compatible UART. - - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2-W) HSCIF compatible UART. - - "renesas,scif-r8a7792" for R8A7792 (R-Car V2H) SCIF compatible UART. - - "renesas,hscif-r8a7792" for R8A7792 (R-Car V2H) HSCIF compatible UART. - - "renesas,scif-r8a7793" for R8A7793 (R-Car M2-N) SCIF compatible UART. - - "renesas,scifa-r8a7793" for R8A7793 (R-Car M2-N) SCIFA compatible UART. - - "renesas,scifb-r8a7793" for R8A7793 (R-Car M2-N) SCIFB compatible UART. - - "renesas,hscif-r8a7793" for R8A7793 (R-Car M2-N) HSCIF compatible UART. - - "renesas,scif-r8a7794" for R8A7794 (R-Car E2) SCIF compatible UART. - - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART. - - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART. - - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. - - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. - - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - - "renesas,scif-r8a7796" for R8A77960 (R-Car M3-W) SCIF compatible UART. - - "renesas,hscif-r8a7796" for R8A77960 (R-Car M3-W) HSCIF compatible UART. - - "renesas,scif-r8a77961" for R8A77961 (R-Car M3-W+) SCIF compatible UART. - - "renesas,hscif-r8a77961" for R8A77961 (R-Car M3-W+) HSCIF compatible UART. - - "renesas,scif-r8a77965" for R8A77965 (R-Car M3-N) SCIF compatible UART. - - "renesas,hscif-r8a77965" for R8A77965 (R-Car M3-N) HSCIF compatible UART. - - "renesas,scif-r8a77970" for R8A77970 (R-Car V3M) SCIF compatible UART. - - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART. - - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART. - - "renesas,hscif-r8a77980" for R8A77980 (R-Car V3H) HSCIF compatible UART. - - "renesas,scif-r8a77990" for R8A77990 (R-Car E3) SCIF compatible UART. - - "renesas,hscif-r8a77990" for R8A77990 (R-Car E3) HSCIF compatible UART. - - "renesas,scif-r8a77995" for R8A77995 (R-Car D3) SCIF compatible UART. - - "renesas,hscif-r8a77995" for R8A77995 (R-Car D3) HSCIF compatible UART. - - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, - - "renesas,rcar-gen2-scif" for R-Car Gen2 and RZ/G1 SCIF compatible UART, - - "renesas,rcar-gen3-scif" for R-Car Gen3 and RZ/G2 SCIF compatible UART, - - "renesas,rcar-gen2-scifa" for R-Car Gen2 and RZ/G1 SCIFA compatible UART, - - "renesas,rcar-gen2-scifb" for R-Car Gen2 and RZ/G1 SCIFB compatible UART, - - "renesas,rcar-gen1-hscif" for R-Car Gen1 HSCIF compatible UART, - - "renesas,rcar-gen2-hscif" for R-Car Gen2 and RZ/G1 HSCIF compatible UART, - - "renesas,rcar-gen3-hscif" for R-Car Gen3 and RZ/G2 HSCIF compatible UART, - - "renesas,scif" for generic SCIF compatible UART. - - "renesas,scifa" for generic SCIFA compatible UART. - - "renesas,scifb" for generic SCIFB compatible UART. - - "renesas,hscif" for generic HSCIF compatible UART. - - "renesas,sci" for generic SCI compatible UART. - - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first, followed by the - family-specific and/or generic versions. - - - reg: Base address and length of the I/O registers used by the UART. - - interrupts: Must contain one or more interrupt-specifiers for the SCIx. - If a single interrupt is expressed, then all events are - multiplexed into this single interrupt. - - If multiple interrupts are provided by the hardware, the order - in which the interrupts are listed must match order below. Note - that some HW interrupt events may be muxed together resulting - in duplicate entries. - The interrupt order is as follows: - 1. Error (ERI) - 2. Receive buffer full (RXI) - 3. Transmit buffer empty (TXI) - 4. Break (BRI) - 5. Data Ready (DRI) - 6. Transmit End (TEI) - - - clocks: Must contain a phandle and clock-specifier pair for each entry - in clock-names. - - clock-names: Must contain "fck" for the SCIx UART functional clock. - Apart from the divided functional clock, there may be other possible - sources for the sampling clock, depending on SCIx variant. - On (H)SCI(F) and some SCIFA, an additional clock may be specified: - - "hsck" for the optional external clock input (on HSCIF), - - "sck" for the optional external clock input (on other variants). - On UARTs equipped with a Baud Rate Generator for External Clock (BRG) - (some SCIF and HSCIF), additional clocks may be specified: - - "brg_int" for the optional internal clock source for the frequency - divider (typically the (AXI or SHwy) bus clock), - - "scif_clk" for the optional external clock source for the frequency - divider (SCIF_CLK). - -Note: Each enabled SCIx UART may have an optional "serialN" alias in the -"aliases" node. - -Optional properties: - - dmas: Must contain a list of two references to DMA specifiers, one for - transmission, and one for reception. - - dma-names: Must contain a list of two DMA names, "tx" and "rx". - - {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the - generic serial DT bindings in serial.txt. - - uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow - control, cfr. the generic serial DT bindings in serial.txt. - -Example: - aliases { - serial0 = &scifa0; - }; - - scifa0: serial@e6c40000 { - compatible = "renesas,scifa-r8a7790", - "renesas,rcar-gen2-scifa", "renesas,scifa"; - reg = <0 0xe6c40000 0 64>; - interrupt-parent = <&gic>; - interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>; - clock-names = "fck"; - dmas = <&dmac0 0x21>, <&dmac0 0x22>; - dma-names = "tx", "rx"; - }; diff --git a/dts/Bindings/serial/renesas,sci.yaml b/dts/Bindings/serial/renesas,sci.yaml new file mode 100644 index 0000000000..4183b7311f --- /dev/null +++ b/dts/Bindings/serial/renesas,sci.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,sci.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communication Interface + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + const: renesas,sci + + reg: + maxItems: 1 + + interrupts: + items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Transmit end interrupt + + interrupt-names: + items: + - const: eri + - const: rxi + - const: txi + - const: tei + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + maxItems: 2 + items: + enum: + - fck # UART functional clock + - sck # optional external clock input + + uart-has-rtscts: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + aliases { + serial0 = &sci0; + }; + + sci0: serial@ffff78 { + compatible = "renesas,sci"; + reg = <0xffff78 8>; + interrupts = <88 0>, <89 0>, <90 0>, <91 0>; + clocks = <&fclk>; + clock-names = "fck"; + }; diff --git a/dts/Bindings/serial/renesas,scif.yaml b/dts/Bindings/serial/renesas,scif.yaml new file mode 100644 index 0000000000..70392b9bd9 --- /dev/null +++ b/dts/Bindings/serial/renesas,scif.yaml @@ -0,0 +1,172 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scif.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communication Interface with FIFO (SCIF) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scif-r7s72100 # RZ/A1H + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r7s9210 # RZ/A2 + + - items: + - enum: + - renesas,scif-r8a7778 # R-Car M1 + - renesas,scif-r8a7779 # R-Car H1 + - const: renesas,rcar-gen1-scif # R-Car Gen1 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r8a7743 # RZ/G1M + - renesas,scif-r8a7744 # RZ/G1N + - renesas,scif-r8a7745 # RZ/G1E + - renesas,scif-r8a77470 # RZ/G1C + - renesas,scif-r8a7790 # R-Car H2 + - renesas,scif-r8a7791 # R-Car M2-W + - renesas,scif-r8a7792 # R-Car V2H + - renesas,scif-r8a7793 # R-Car M2-N + - renesas,scif-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-scif # R-Car Gen2 and RZ/G1 + - const: renesas,scif # generic SCIF compatible UART + + - items: + - enum: + - renesas,scif-r8a774a1 # RZ/G2M + - renesas,scif-r8a774b1 # RZ/G2N + - renesas,scif-r8a774c0 # RZ/G2E + - renesas,scif-r8a7795 # R-Car H3 + - renesas,scif-r8a7796 # R-Car M3-W + - renesas,scif-r8a77961 # R-Car M3-W+ + - renesas,scif-r8a77965 # R-Car M3-N + - renesas,scif-r8a77970 # R-Car V3M + - renesas,scif-r8a77980 # R-Car V3H + - renesas,scif-r8a77990 # R-Car E3 + - renesas,scif-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-scif # R-Car Gen3 and RZ/G2 + - const: renesas,scif # generic SCIF compatible UART + + reg: + maxItems: 1 + + interrupts: + oneOf: + - items: + - description: A combined interrupt + - items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Transmit End interrupt + - items: + - description: Error interrupt + - description: Receive buffer full interrupt + - description: Transmit buffer empty interrupt + - description: Break interrupt + - description: Data Ready interrupt + - description: Transmit End interrupt + + interrupt-names: + oneOf: + - items: + - const: eri + - const: rxi + - const: txi + - const: tei + - items: + - const: eri + - const: rxi + - const: txi + - const: bri + - const: dri + - const: tei + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + enum: + - fck # UART functional clock + - sck # optional external clock input + - brg_int # optional internal clock source for BRG frequency divider + - scif_clk # optional external clock source for BRG frequency divider + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scif + - renesas,rcar-gen3-scif +then: + required: + - resets + +examples: + - | + #include <dt-bindings/clock/r8a7791-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7791-sysc.h> + aliases { + serial0 = &scif0; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a7791", "renesas,rcar-gen2-scif", + "renesas,scif"; + reg = <0xe6e60000 64>; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 721>, <&cpg CPG_CORE R8A7791_CLK_ZS>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x29>, <&dmac0 0x2a>, <&dmac1 0x29>, <&dmac1 0x2a>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 721>; + }; diff --git a/dts/Bindings/serial/renesas,scifa.yaml b/dts/Bindings/serial/renesas,scifa.yaml new file mode 100644 index 0000000000..b28bcb2688 --- /dev/null +++ b/dts/Bindings/serial/renesas,scifa.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scifa.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communications Interface with FIFO A (SCIFA) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scifa-r8a73a4 # R-Mobile APE6 + - renesas,scifa-r8a7740 # R-Mobile A1 + - renesas,scifa-sh73a0 # SH-Mobile AG5 + - const: renesas,scifa # generic SCIFA compatible UART + + - items: + - enum: + - renesas,scifa-r8a7743 # R8A7743 RZ/G1M + - renesas,scifa-r8a7744 # R8A7744 RZ/G1N + - renesas,scifa-r8a7745 # R8A7745 RZ/G1E + - renesas,scifa-r8a7790 # R8A7790 R-Car H2 + - renesas,scifa-r8a7791 # R8A7791 R-Car M2-W + - renesas,scifa-r8a7793 # R8A7793 R-Car M2-N + - renesas,scifa-r8a7794 # R8A7794 R-Car E2 + - const: renesas,rcar-gen2-scifa # R-Car Gen2 and RZ/G1 + - const: renesas,scifa # generic SCIFA compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + enum: + - fck # UART functional clock + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scifa +then: + required: + - resets + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + aliases { + serial0 = &scifa0; + }; + + scifa0: serial@e6c40000 { + compatible = "renesas,scifa-r8a7790", "renesas,rcar-gen2-scifa", + "renesas,scifa"; + reg = <0xe6c40000 64>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 204>; + clock-names = "fck"; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 204>; + dmas = <&dmac0 0x21>, <&dmac0 0x22>, <&dmac1 0x21>, <&dmac1 0x22>; + dma-names = "tx", "rx", "tx", "rx"; + }; diff --git a/dts/Bindings/serial/renesas,scifb.yaml b/dts/Bindings/serial/renesas,scifb.yaml new file mode 100644 index 0000000000..57205cb1dc --- /dev/null +++ b/dts/Bindings/serial/renesas,scifb.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/renesas,scifb.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas Serial Communications Interface with FIFO B (SCIFB) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: serial.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,scifb-r8a73a4 # R-Mobile APE6 + - renesas,scifb-r8a7740 # R-Mobile A1 + - renesas,scifb-sh73a0 # SH-Mobile AG5 + - const: renesas,scifb # generic SCIFB compatible UART + + - items: + - enum: + - renesas,scifb-r8a7743 # RZ/G1M + - renesas,scifb-r8a7744 # RZ/G1N + - renesas,scifb-r8a7745 # RZ/G1E + - renesas,scifb-r8a7790 # R-Car H2 + - renesas,scifb-r8a7791 # R-Car M2-W + - renesas,scifb-r8a7793 # R-Car M2-N + - renesas,scifb-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-scifb # R-Car Gen2 and RZ/G1 + - const: renesas,scifb # generic SCIFB compatible UART + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + enum: + - fck # UART functional clock + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + +if: + properties: + compatible: + contains: + enum: + - renesas,rcar-gen2-scifb +then: + required: + - resets + +examples: + - | + #include <dt-bindings/clock/r8a7740-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + scifb: serial@e6c30000 { + compatible = "renesas,scifb-r8a7740", "renesas,scifb"; + reg = <0xe6c30000 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7740_CLK_SCIFB>; + clock-names = "fck"; + power-domains = <&pd_a3sp>; + }; diff --git a/dts/Bindings/serial/serial.txt b/dts/Bindings/serial/serial.txt deleted file mode 100644 index 863c289375..0000000000 --- a/dts/Bindings/serial/serial.txt +++ /dev/null @@ -1,56 +0,0 @@ -Generic Serial DT Bindings - -This document lists a set of generic properties for describing UARTs in a -device tree. Whether these properties apply to a particular device depends on -the DT bindings for the actual device. - -Optional properties: - - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's CTS line. - - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DCD line. - - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DSR line. - - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DTR line. - - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's RNG line. - - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's RTS line. - - - uart-has-rtscts: The presence of this property indicates that the - UART has dedicated lines for RTS/CTS hardware flow control, and that - they are available for use (wired and enabled by pinmux configuration). - This depends on both the UART hardware and the board wiring. - Note that this property is mutually-exclusive with "cts-gpios" and - "rts-gpios" above, unless support is provided to switch between modes - dynamically. - - -Examples: - - uart1: serial@48022000 { - compatible = "ti,am3352-uart", "ti,omap3-uart"; - ti,hwmods = "uart2"; - clock-frequency = <48000000>; - reg = <0x48022000 0x2000>; - interrupts = <73>; - dmas = <&edma 28 0>, <&edma 29 0>; - dma-names = "tx", "rx"; - dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; - dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; - dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; - rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; - cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; - rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; - }; - - scifa4: serial@e6c80000 { - compatible = "renesas,scifa-sh73a0", "renesas,scifa"; - reg = <0xe6c80000 0x100>; - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>; - clock-names = "fck"; - power-domains = <&pd_a3sp>; - uart-has-rtscts; - }; diff --git a/dts/Bindings/serial/serial.yaml b/dts/Bindings/serial/serial.yaml new file mode 100644 index 0000000000..53204d90d0 --- /dev/null +++ b/dts/Bindings/serial/serial.yaml @@ -0,0 +1,131 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/serial.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Serial Interface Generic DT Bindings + +maintainers: + - Rob Herring <robh@kernel.org> + - Greg Kroah-Hartman <gregkh@linuxfoundation.org> + +description: + This document lists a set of generic properties for describing UARTs in a + device tree. Whether these properties apply to a particular device depends + on the DT bindings for the actual device. + + Each enabled UART may have an optional "serialN" alias in the "aliases" node, + where N is the port number (non-negative decimal integer) as printed on the + label next to the physical port. + +properties: + $nodename: + pattern: "^serial(@.*)?$" + + cts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's CTS line. + + dcd-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DCD line. + + dsr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DSR line. + + dtr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DTR line. + + rng-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RNG line. + + rts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RTS line. + + uart-has-rtscts: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the UART has dedicated lines + for RTS/CTS hardware flow control, and that they are available for use + (wired and enabled by pinmux configuration). This depends on both the + UART hardware and the board wiring. + +if: + required: + - uart-has-rtscts +then: + properties: + cts-gpios: false + rts-gpios: false + +patternProperties: + ".*": + if: + type: object + then: + description: + Serial attached devices shall be a child node of the host UART device + the slave device is attached to. It is expected that the attached + device is the only child node of the UART device. The slave device node + name shall reflect the generic type of device for the node. + + properties: + compatible: + description: + Compatible of the device connected to the serial port. + + max-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The maximum baud rate the device operates at. + This should only be present if the maximum is less than the slave + device can support. For example, a particular board has some + signal quality issue or the host processor can't support higher + baud rates. + + current-speed: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The current baud rate the device operates at. + This should only be present in case a driver has no chance to know + the baud rate of the slave device. + Examples: + * device supports auto-baud + * the rate is setup by a bootloader and there is no way to reset + the device + * device baud rate is configured by its firmware but there is no + way to request the actual settings + + required: + - compatible + +examples: + - | + serial@1234 { + compatible = "ns16550a"; + reg = <0x1234 0x20>; + interrupts = <1>; + + bluetooth { + compatible = "brcm,bcm43341-bt"; + interrupt-parent = <&gpio>; + interrupts = <10>; + }; + }; diff --git a/dts/Bindings/serial/slave-device.txt b/dts/Bindings/serial/slave-device.txt deleted file mode 100644 index 40110e0196..0000000000 --- a/dts/Bindings/serial/slave-device.txt +++ /dev/null @@ -1,45 +0,0 @@ -Serial Slave Device DT binding - -This documents the binding structure and common properties for serial -attached devices. Common examples include Bluetooth, WiFi, NFC and GPS -devices. - -Serial attached devices shall be a child node of the host UART device the -slave device is attached to. It is expected that the attached device is -the only child node of the UART device. The slave device node name shall -reflect the generic type of device for the node. - -Required Properties: - -- compatible : A string reflecting the vendor and specific device the node - represents. - -Optional Properties: - -- max-speed : The maximum baud rate the device operates at. This should - only be present if the maximum is less than the slave device - can support. For example, a particular board has some signal - quality issue or the host processor can't support higher - baud rates. -- current-speed : The current baud rate the device operates at. This should - only be present in case a driver has no chance to know - the baud rate of the slave device. - Examples: - * device supports auto-baud - * the rate is setup by a bootloader and there is no - way to reset the device - * device baud rate is configured by its firmware but - there is no way to request the actual settings - -Example: - -serial@1234 { - compatible = "ns16550a"; - interrupts = <1>; - - bluetooth { - compatible = "brcm,bcm43341-bt"; - interrupt-parent = <&gpio>; - interrupts = <10>; - }; -}; diff --git a/dts/Bindings/serial/snps-dw-apb-uart.yaml b/dts/Bindings/serial/snps-dw-apb-uart.yaml index b420025426..b962f8db4c 100644 --- a/dts/Bindings/serial/snps-dw-apb-uart.yaml +++ b/dts/Bindings/serial/snps-dw-apb-uart.yaml @@ -27,6 +27,7 @@ properties: - rockchip,rk3066-uart - rockchip,rk3188-uart - rockchip,rk3288-uart + - rockchip,rk3308-uart - rockchip,rk3328-uart - rockchip,rk3368-uart - rockchip,rk3399-uart diff --git a/dts/Bindings/serial/socionext,uniphier-uart.yaml b/dts/Bindings/serial/socionext,uniphier-uart.yaml new file mode 100644 index 0000000000..09a3030085 --- /dev/null +++ b/dts/Bindings/serial/socionext,uniphier-uart.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/socionext,uniphier-uart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier UART controller + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +properties: + compatible: + const: socionext,uniphier-uart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + auto-flow-control: + description: enable automatic flow control support. + $ref: /schemas/types.yaml#/definitions/flag + +required: + - compatible + - reg + - interrupts + - clocks + +examples: + - | + aliases { + serial0 = &serial0; + }; + + serial0: serial@54006800 { + compatible = "socionext,uniphier-uart"; + reg = <0x54006800 0x40>; + interrupts = <0 33 4>; + clocks = <&uart_clk>; + }; diff --git a/dts/Bindings/serial/uniphier-uart.txt b/dts/Bindings/serial/uniphier-uart.txt deleted file mode 100644 index 7a1bf02bb8..0000000000 --- a/dts/Bindings/serial/uniphier-uart.txt +++ /dev/null @@ -1,22 +0,0 @@ -UniPhier UART controller - -Required properties: -- compatible: should be "socionext,uniphier-uart". -- reg: offset and length of the register set for the device. -- interrupts: a single interrupt specifier. -- clocks: phandle to the input clock. - -Optional properties: --auto-flow-control: enable automatic flow control support. - -Example: - aliases { - serial0 = &serial0; - }; - - serial0: serial@54006800 { - compatible = "socionext,uniphier-uart"; - reg = <0x54006800 0x40>; - interrupts = <0 33 4>; - clocks = <&uart_clk>; - }; |