dts: update to v5.8-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

3 files changed, 211 insertions, 37 deletions

diff --git a/dts/Bindings/iio/imu/adi,adis16475.yaml b/dts/Bindings/iio/imu/adi,adis16475.yaml
new file mode 100644
index 0000000000..208faaffa5
--- /dev/null
+++ b/dts/Bindings/iio/imu/adi,adis16475.yaml
@@ -0,0 +1,136 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/imu/adi,adis16475.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADIS16475 and similar IMUs
+
+maintainers:
+  - Nuno Sá <nuno.sa@analog.com>
+
+description: |
+  Analog Devices ADIS16475 and similar IMUs
+  https://www.analog.com/media/en/technical-documentation/data-sheets/ADIS16475.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,adis16475-1
+      - adi,adis16475-2
+      - adi,adis16475-3
+      - adi,adis16477-1
+      - adi,adis16477-2
+      - adi,adis16477-3
+      - adi,adis16470
+      - adi,adis16465-1
+      - adi,adis16465-2
+      - adi,adis16465-3
+      - adi,adis16467-1
+      - adi,adis16467-2
+      - adi,adis16467-3
+      - adi,adis16500
+      - adi,adis16505-1
+      - adi,adis16505-2
+      - adi,adis16505-3
+      - adi,adis16507-1
+      - adi,adis16507-2
+      - adi,adis16507-3
+
+  reg:
+    maxItems: 1
+
+  spi-cpha: true
+
+  spi-cpol: true
+
+  spi-max-frequency:
+    maximum: 2000000
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      Must be the device tree identifier of the RESET pin. If specified,
+      it will be asserted during driver probe. As the line is active low,
+      it should be marked GPIO_ACTIVE_LOW.
+    maxItems: 1
+
+  adi,sync-mode:
+    description:
+      Configures the device SYNC pin. The following modes are supported
+      0 - output_sync
+      1 - direct_sync
+      2 - scaled_sync
+      3 - pulse_sync
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 3
+
+  adi,scaled-output-hz:
+    description:
+      This property must be present if the clock mode is scaled-sync through
+      clock-names property. In this mode, the input clock can have a range
+      of 1Hz to 128HZ which must be scaled to originate an allowable sample
+      rate. This property specifies that rate.
+    minimum: 1900
+    maximum: 2100
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - spi-cpha
+  - spi-cpol
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - adi,adis16500
+              - adi,adis16505-1
+              - adi,adis16505-2
+              - adi,adis16505-3
+              - adi,adis16507-1
+              - adi,adis16507-2
+              - adi,adis16507-3
+
+    then:
+      properties:
+        adi,sync-mode:
+          minimum: 0
+          maximum: 2
+
+  - if:
+      properties:
+        adi,sync-mode:
+          enum: [1, 2, 3]
+
+    then:
+      dependencies:
+        adi,sync-mode: [ clocks ]
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            adis16475: adis16475-3@0 {
+                    compatible = "adi,adis16475-3";
+                    reg = <0>;
+                    spi-cpha;
+                    spi-cpol;
+                    spi-max-frequency = <2000000>;
+                    interrupts = <4 IRQ_TYPE_EDGE_RISING>;
+                    interrupt-parent = <&gpio>;
+            };
+    };
+...
diff --git a/dts/Bindings/iio/imu/bmi160.txt b/dts/Bindings/iio/imu/bmi160.txt
deleted file mode 100644
index 900c169de0..0000000000
--- a/dts/Bindings/iio/imu/bmi160.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope
-and externally connectable Magnetometer
-
-https://www.bosch-sensortec.com/bst/products/all_products/bmi160
-
-Required properties:
- - compatible : should be "bosch,bmi160"
- - reg : the I2C address or SPI chip select number of the sensor
- - spi-max-frequency : set maximum clock frequency (only for SPI)
-
-Optional properties:
- - interrupts : interrupt mapping for IRQ
- - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt
-   input, set to "INT2" if INT2 pin should be used instead
- - drive-open-drain : set if the specified interrupt pin should be configured as
-   open drain. If not set, defaults to push-pull.
-
-Examples:
-
-bmi160@68 {
-	compatible = "bosch,bmi160";
-	reg = <0x68>;
-
-	interrupt-parent = <&gpio4>;
-	interrupts = <12 IRQ_TYPE_EDGE_RISING>;
-	interrupt-names = "INT1";
-};
-
-bmi160@0 {
-	compatible = "bosch,bmi160";
-	reg = <0>;
-	spi-max-frequency = <10000000>;
-
-	interrupt-parent = <&gpio2>;
-	interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
-	interrupt-names = "INT2";
-};
diff --git a/dts/Bindings/iio/imu/bosch,bmi160.yaml b/dts/Bindings/iio/imu/bosch,bmi160.yaml
new file mode 100644
index 0000000000..0d0ef84e22
--- /dev/null
+++ b/dts/Bindings/iio/imu/bosch,bmi160.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/imu/bosch,bmi160.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bosch BMI160
+
+maintainers:
+  - Jonathan Cameron <jic23@kernel.org>
+
+description: |
+  Inertial Measurement Unit with Accelerometer, Gyroscope and externally
+  connectable Magnetometer
+  https://www.bosch-sensortec.com/bst/products/all_products/bmi160
+
+properties:
+  compatible:
+    const: bosch,bmi160
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-names:
+    enum:
+      - INT1
+      - INT2
+    description: |
+      set to "INT1" if INT1 pin should be used as interrupt input, set
+      to "INT2" if INT2 pin should be used instead
+
+  drive-open-drain:
+    description: |
+      set if the specified interrupt pin should be configured as
+      open drain. If not set, defaults to push-pull.
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    // Example for I2C
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bmi160@68 {
+                compatible = "bosch,bmi160";
+                reg = <0x68>;
+                interrupt-parent = <&gpio4>;
+                interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+                interrupt-names = "INT1";
+        };
+    };
+  - |
+    // Example for SPI
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bmi160@0 {
+                compatible = "bosch,bmi160";
+                reg = <0>;
+                spi-max-frequency = <10000000>;
+                interrupt-parent = <&gpio2>;
+                interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+                interrupt-names = "INT2";
+        };
+    };