Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 58 insertions, 0 deletions

diff --git a/dts/Bindings/media/samsung-s5k5baf.txt b/dts/Bindings/media/samsung-s5k5baf.txt
new file mode 100644
index 0000000000..1f51e0439c
--- /dev/null
+++ b/dts/Bindings/media/samsung-s5k5baf.txt
@@ -0,0 +1,58 @@
+Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP
+--------------------------------------------------------------------
+
+Required properties:
+
+- compatible	  : "samsung,s5k5baf";
+- reg		  : I2C slave address of the sensor;
+- vdda-supply	  : analog power supply 2.8V (2.6V to 3.0V);
+- vddreg-supply	  : regulator input power supply 1.8V (1.7V to 1.9V)
+		    or 2.8V (2.6V to 3.0);
+- vddio-supply	  : I/O power supply 1.8V (1.65V to 1.95V)
+		    or 2.8V (2.5V to 3.1V);
+- stbyn-gpios	  : GPIO connected to STDBYN pin;
+- rstn-gpios	  : GPIO connected to RSTN pin;
+- clocks	  : list of phandle and clock specifier pairs
+		    according to common clock bindings for the
+		    clocks described in clock-names;
+- clock-names	  : should include "mclk" for the sensor's master clock;
+
+Optional properties:
+
+- clock-frequency : the frequency at which the "mclk" clock should be
+		    configured to operate, in Hz; if this property is not
+		    specified default 24 MHz value will be used.
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt. The following are properties specific to those
+nodes.
+
+endpoint node
+-------------
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+	       video-interfaces.txt. If present it should be <1> - the device
+	       supports only one data lane without re-mapping.
+
+Example:
+
+s5k5bafx@2d {
+	compatible = "samsung,s5k5baf";
+	reg = <0x2d>;
+	vdda-supply = <&cam_io_en_reg>;
+	vddreg-supply = <&vt_core_15v_reg>;
+	vddio-supply = <&vtcam_reg>;
+	stbyn-gpios = <&gpl2 0 1>;
+	rstn-gpios = <&gpl2 1 1>;
+	clock-names = "mclk";
+	clocks = <&clock_cam 0>;
+	clock-frequency = <24000000>;
+
+	port {
+		s5k5bafx_ep: endpoint {
+			remote-endpoint = <&csis1_ep>;
+			data-lanes = <1>;
+		};
+	};
+};